2022 Yeti 160E

Yes, it fits a standard-sized water bottle in the front triangle with a piggy-back shock. Use a side-entry cage for easy access.

220mm rotor with a brake adaptor, 180mm rotor without.

You should only replace them with genuine Yeti parts. Yeti can't qualify and ensure other products are safe to use on its frames. If you use parts from other brands, all warranties will be voided, and you assume full liability.

205x65mm Trunnion shock. It can be locked out, but Yeti recommends running it fully open for the best compliance and traction.

Custom hardware on both sides. The lower shock hardware spacing is M8x43.69mm. It's adjustable so you can rune the leverage rate to suit your riding style or the terrain you're riding. Check your owners manual for more information.

Integrated 41mm/52mm tapered headset. The bearings are contained in the head tube for a lower ride height, increased stiffness, and easier installation.

It's made with an integrated headset with the cups molded into the frame. So you can easily drop the bearings into the cups. There are some aftermarket anglesets for this style headset. But the frame was not tested for these, so they shouldn't be used.

It comes with a Lifetime Manufacturer's Warranty.

Yes, it's compatible with air and coil-sprung shocks.

No, it has a custom top guide mount that works with the OneUp top guide.

Yes, it has routing options for stealth only.

31.6mm seat post.

Some parts from Fox, Shimano, SRAM and other brands are standardized. Check with a mechanic to make sure your parts are the correct standard. And ensure that they are correctly and securely mounted to the bike without any interference.

36.4mm seat collar.

It's possible but not recommended. It would lower your BB too much and slacken your head tube angle and seat tube angle. If those changes suit your ride style, then you can do it.

53mm boost chainline.

This bike has an EP8 drive unit, which replaces the BB interface. The crank spindle is built into the drive unit. All you have to do is bolt on any Shimano EP8 compatible crank arm.

51mm top cap rather than the standard cap diameter. That's because it was tested to Yeti's more rigorous DH test standards, which require a larger HT wall thickness.

SRAM's Universal Derailleur Hanger at 12x148mm spacing. This axle is only compatible with frames designed with the Universal Derailleur Hanger.

Start with 30% sag or 19.5mm of shock stroke for optimal pedaling efficiency and terrain compliance. You can also go slightly above or below that amount to suit your preference. Be sure to set it at your normal riding weight, gear included.

34t round ring.

All parts and mounts should be serviced at a certified shop.

Any authorized Yeti dealer.

Check the instructions in the Shimano STEPS app.

Directly from Shimano. You can also buy battery covers on the Yeti website or at your local Yeti dealer.

Don't throw it away with your other garbage. Check the manual or contact your Yeti dealer for proper disposal.

Follow this link for troubleshooting tips - https://bike.shimano.com/en-EU/e-tube/project.html.

It depends on the terrain, your riding style, and personal preference. You should experiment to see what works best for you. The stock setting is 30%, and that's a great place to start.

It depends on your inseam. You can run any travel as long as you're above the minimum insert mark, your tires don't rub on your saddle, and your dropper doesn't bottom out in the frame. low your tire rubs on your saddle. Yeti runs 125mm drop on XS/S frames, 150mm drop on M, and 175mm drop on L/XL.

No, the downtube cover is attached to the battery. Without it, the internal frame and electrical components will be damaged by the elements.

No, this bike is only compatible with the BT-E8036 Shimano 630Wh battery.

The battery size is larger than what's typically allowed on a plane. Check your local regulations before you fly.

The maximum capacity is 630 watt hours. But it depends on your weight, location, gradient, selected mode, ambient temperature, and more. The range function on the display will give you the best estimate

The Shimano STEPS system is water resistant and the frame drains water. You shouldn't submerse the bike in water or get a power wash.

There are Shimano STEPS for the drive unit, and no special tools are required.

This bike is fully compatible with SRAM drivetrains. You have to use the stock Shimano chainring spider that comes on the bike. It's designed to interface with the EP8 drive unit spindle. So all you have to do is remove the chainring bolts and replace the chainring with a SRAM 104 BCD 34 tooth chainring. You don't have to replace the crankarms. But you should replace the complete drivetrain, including derailleur, shifter, cassette, chain, and chainring.

Yes, the maximum recommended fork travel is 190mm.

You can pedal without the battery or motor. The loss of power might not be from a depleted battery. Try turning it off and back on. If the problem persists, contact Yeti customer service.

Press the button on the bottom of the display to get to the Bluetooth-LE menu. Then connect your device through the E-tube app.